CLI - System - Revision history

Shin at 01:51, 28 January 2022

2022-01-28T01:51:15Z

Shin at 08:19, 17 June 2021

2021-06-17T08:19:28Z

Shin: /* datetime */

2021-05-18T04:47:57Z

datetime

Shin: /* datetime */

2021-05-18T04:47:30Z

datetime

Shin: /* datetime */

2021-05-18T04:47:19Z

datetime

Shin: /* datetime */

2021-05-18T04:46:29Z

datetime

Shin: /* configuration */

2021-05-18T04:46:14Z

configuration

Shin: /* datetime */

2021-05-18T04:45:40Z

datetime

Shin: /* Configuring datetime = */

2021-05-18T04:45:26Z

Configuring datetime =

Shin: /* datetime */

2021-05-18T04:45:03Z

datetime

@@ Line 81: / Line 81: @@
 Note that if you manually change the system time and date while the NTP is enabled, you encounter the "''Failed to set time: Automatic time synchronization is enabled''" error. Therefore you need to disable the NTP before configuring the system time and date manually.
   LYSH@MyHostName# configure
-  configure# datetime 2021-04-27 13:00:00
+  LYSH@MyHostName(config)# datetime 2021-04-27 13:00:00
                 Local time: Tue 2021-04-27 13:00:00:49 KST
             Universal time: Tue 2021-04-27 04:00:00 UTC
@@ Line 94: / Line 94: @@
 <pre>
 LYSH@MyHostName# configure
-configure# tiemzone
+LYSH@MyHostName(config)# tiemzone
 </pre>
@@ Line 147: / Line 147: @@
 <pre>
 LYSH@MyHostName# configure
-configure# system reset log
+LYSH@MyHostName(config)# system reset log
 FACTORY RESET WARNING!!
 All of the configurations will be restored and you will lose data.

@@ Line 192: / Line 192: @@
   Apt caches*         :75M
 Libraries           :2.6G
 </pre>

@@ Line 78: / Line 78: @@
 ===== Configuring datetime =====
-To change the system time and date, enter the <code>datetime {format}</code>. The format must be 'yyyy-mm-dd hh24:mi:ss'.<br>
+To change the system time and date, enter the <code>datetime {format}</code> on the configuration mode. The format must be 'yyyy-mm-dd hh24:mi:ss'.<br>
 Note that if you manually change the system time and date while the NTP is enabled, you encounter the "''Failed to set time: Automatic time synchronization is enabled''" error. Therefore you need to disable the NTP before configuring the system time and date manually.
   LYSH@MyHostName# configure

@@ Line 77: / Line 77: @@
 If the Local time or Time zone is incorrect to your locale, you should change it in the [[CLI - Configuration Mode | configuration mode]] using "datetime" or "timezone" command.
-====== Configuring datetime ======
+===== Configuring datetime =====
 To change the system time and date, enter the <code>datetime {format}</code>. The format must be 'yyyy-mm-dd hh24:mi:ss'.<br>
 Note that if you manually change the system time and date while the NTP is enabled, you encounter the "''Failed to set time: Automatic time synchronization is enabled''" error. Therefore you need to disable the NTP before configuring the system time and date manually.
@@ Line 90: / Line 90: @@
            RTC in local TZ: no
-====== Configuring timezone ======
+===== Configuring timezone =====
 You can configure the timezone of the device.
 <pre>

@@ Line 78: / Line 78: @@
 ====== Configuring datetime ======
 To change the system time and date, enter the <code>datetime {format}</code>. The format must be 'yyyy-mm-dd hh24:mi:ss'.<br>
 Note that if you manually change the system time and date while the NTP is enabled, you encounter the "''Failed to set time: Automatic time synchronization is enabled''" error. Therefore you need to disable the NTP before configuring the system time and date manually.

@@ Line 34: / Line 34: @@
 </pre>
-==== configuration ====
+==== Veryfying global configuration ====
 To verity the [[Variables of Global Configurations | global configurations]] of the imRAD, enter the <code>show config</code> command.
 <pre>

← Older revision		Revision as of 04:45, 18 May 2021
Line 76:		Line 76:

	If the Local time or Time zone is incorrect to your locale, you should change it in the [[CLI - Configuration Mode \| configuration mode]] using "datetime" or "timezone" command.		If the Local time or Time zone is incorrect to your locale, you should change it in the [[CLI - Configuration Mode \| configuration mode]] using "datetime" or "timezone" command.
		+
		+	===== Configuring datetime ======
		+	To show the system time and date, enter the <code>show datetime</code> command.
		+	<pre>
		+	LYSH@MyHostName# show datetime
		+	Local time: Tue 2021-04-27 13:32:46 KST
		+	Universal time: Tue 2021-04-27 04:32:46 UTC
		+	RTC time: Tue 2021-04-27 04:32:46
		+	Time zone: Asia/Seoul (KST, +0900)
		+	System clock synchronized: yes
		+	NTP service: active
		+	RTC in local TZ: no
		+	</pre>
		+
		+
		+	To change the system time and date, enter the <code>datetime {format}</code>. The format must be 'yyyy-mm-dd hh24:mi:ss'.<br>
		+	Note that if you manually change the system time and date while the NTP is enabled, you encounter the "''Failed to set time: Automatic time synchronization is enabled''" error. Therefore you need to disable the NTP before configuring the system time and date manually.
		+	LYSH@MyHostName# configure
		+	configure# datetime 2021-04-27 13:00:00
		+	Local time: Tue 2021-04-27 13:00:00:49 KST
		+	Universal time: Tue 2021-04-27 04:00:00 UTC
		+	RTC time: Tue 2021-04-27 04:00:00
		+	Time zone: Asia/Seoul (KST, +0900)
		+	System clock synchronized: yes
		+	NTP service: active
		+	RTC in local TZ: no
		+
		+	===== timezone =====
		+	You can configure the timezone of the device.
		+	<pre>
		+	LYSH@MyHostName# configure
		+	configure# tiemzone
		+	</pre>
		+
		+	===== Configuring timezone =====
		+	You can configure the timezone of the device.
		+	<pre>
		+	LYSH@MyHostName# configure
		+	configure# tiemzone
		+	</pre>

	==== hardware ====		==== hardware ====