Command Line Interface (CLI, LYSH) - Revision history

송재호 at 06:24, 16 June 2021

2021-06-16T06:24:38Z

Shin at 07:55, 20 May 2021

2021-05-20T07:55:30Z

Shin at 07:01, 20 May 2021

2021-05-20T07:01:32Z

Shin at 05:48, 20 May 2021

2021-05-20T05:48:15Z

Shin at 05:47, 20 May 2021

2021-05-20T05:47:24Z

Shin at 05:45, 20 May 2021

2021-05-20T05:45:25Z

Shin at 05:45, 20 May 2021

2021-05-20T05:45:05Z

Shin at 05:44, 20 May 2021

2021-05-20T05:44:43Z

Shin at 05:44, 20 May 2021

2021-05-20T05:44:22Z

Shin at 05:43, 20 May 2021

2021-05-20T05:43:57Z

@@ Line 1: / Line 1: @@
-We provide Command Line Interface (CLI), the name is LYSH, that is used for configuring, monitoring, and maintaining the imRAD devices.
+We provide Command Line Interface (CLI), the name is LYSH, which is used for configuring, monitoring, and maintaining the imRAD devices.
 The CLI allows you to directly execute commands, whether using a '''console(i.e. Serial Communication)''' or using remote access methods such as '''Secure Shell (SSH, port 22)'''.
 {{note|The imRAD device does '''not allow telnet''' access.}}
@@ Line 9: / Line 9: @@
 '''If you log in with the default, you must change the default password. If not, you can't access the CLI before changing the password.'''
-The CLI has two command line modes: '''user mode and configuration mode'''. By default, user mode is where you begin the session with the imRAD devices. The user mode contains commands that you can use to see logs, the status of services, configurations, system variables and information, and so on. You can run some Linux commands in the user mode.
+The CLI has two command line modes: '''user mode and configuration mode'''. By default, user mode is where you begin the session with the imRAD devices. The user mode contains commands that you can use to see logs, the status of services, configurations, system variables and information, and so on. You can run some Linux commands in user mode.
 The configuration mode enables to have you can do changes on device configuration such as hostname, Database properties, IP address, nameserver, tiemzone, ntp, ufw, failover, etc. To enter the configuration mode, type the <code>configure</code> command in the user mode.
@@ Line 22: / Line 22: @@
 positional arguments:
      apache2                             show the status of apache2 service
-     command                             show all or releated commands
+     command                             show all or related commands
      config                              show config files
      datetime                            show current time and zone

← Older revision		Revision as of 07:55, 20 May 2021
Line 68:		Line 68:
	.....		.....
	</pre>		</pre>
−
−	~~The followings are main commands and you can read about other commands by searching a keyword on this page.~~
−	~~# [[CLI - Networking]]~~
−	~~# [[CLI - Hostname]]~~
−	~~# [[CLI - Services(daemons)]]~~
−	~~# [[CLI - Log ]]~~
−	~~# [[CLI - System]]~~
−	~~# [[CLI - Database]]~~
−	~~# [[CLI - System Failover]]~~
−	~~# [[CLI - Updating system]]~~
−	~~# [[CLI - shutdown and reboot]]~~
−	~~# [[CLI - Configuration Mode]]~~
−	~~# [[CLI - ufw \| CLI - ufw(firewall)]]~~
−	~~# [[CLI - User and Session]]~~

@@ Line 3: / Line 3: @@
 {{note|The imRAD device does '''not allow telnet''' access.}}
-If you access the imRAD devices via a console port that is located in front of the device, the baud rate(speed) is 115,200 and the serial port type is an RJ-45 connector.
+If you access the console port, the port is located in front of the device and the type is RJ45 connector.
 The default or initial Username and Password are <span style="font-family:Courier;font-weight:bold;font-size:large;">ladmin</span> and <span style="font-family:Courier;font-weight:bold;font-size:large;>1111</span> respectively.<br>

@@ Line 8: / Line 8: @@
 '''If you log in with the default, you must change the default password. If not, you can't access the CLI before changing the password.'''
-The CLI has two command line modes: user mode and configuration mode. By default, user mode is where you begin the session with the imRAD devices. The user mode contains commands that you can use to see logs, the status of services, configurations, system variables and information, and so on. You can run some Linux commands in the user mode.
+The CLI has two command line modes: '''user mode and configuration mode'''. By default, user mode is where you begin the session with the imRAD devices. The user mode contains commands that you can use to see logs, the status of services, configurations, system variables and information, and so on. You can run some Linux commands in the user mode.
 The configuration mode enables to have you can do changes on device configuration such as hostname, Database properties, IP address, nameserver, tiemzone, ntp, ufw, failover, etc. To enter the configuration mode, type the <code>configure</code> command in the user mode.

@@ Line 1: / Line 1: @@
 We provide Command Line Interface (CLI), the name is LYSH, that is used for configuring, monitoring, and maintaining the imRAD devices.
-The CLI allows you to directly execute commands, whether using a '''console''' or using remote access methods such as '''Secure Shell (SSH, port 22)'''.
+The CLI allows you to directly execute commands, whether using a '''console(i.e. Serial Communication)''' or using remote access methods such as '''Secure Shell (SSH, port 22)'''.
 {{note|The imRAD device does '''not allow telnet''' access.}}