Getting started - Revision history

Shin at 09:58, 3 February 2022

2022-02-03T09:58:40Z

2022-02-03T09:57:13Z

2022-02-03T09:55:35Z

2022-01-28T01:47:42Z

2021-07-08T02:00:13Z

2021-07-08T01:58:18Z

2021-06-17T07:14:58Z

2021-06-17T07:11:10Z

2021-06-17T07:09:53Z

2021-05-24T02:17:24Z

@@ Line 19: / Line 19: @@
 After accessing the CLI, you have to set an IP address on the device. Please refer to the [[CLI - Networking]] section to know how to configure an IP address. Following is a simple example.
-{{note|If you use the same address as the IP address that was configured in the [[Product activation|activation]] step, skip this step. If you use a different IP address, delete the existing address by <code>ip delete</code> command, and then enter a new IP address.}}
+{{note|If you use the same address as the IP address that was configured in the [[Product activation|activation]] step, skip this step. If you use a different IP address, delete the existing address by <code>ip delete <interface name> <ip/subnet></code> command, and then enter a new IP address.}}
 <pre>
 LYSH@MyHostName# configure			 // Enters configuration mode.

@@ Line 19: / Line 19: @@
 After accessing the CLI, you have to set an IP address on the device. Please refer to the [[CLI - Networking]] section to know how to configure an IP address. Following is a simple example.
-{{note|If you use the same address as the IP address that was configured in the activation step, skip this step. If you use a different IP address, delete the existing address by <code>ip delete</code> command, and then enter a new IP address.}}
+{{note|If you use the same address as the IP address that was configured in the [[Product activation|activation]] step, skip this step. If you use a different IP address, delete the existing address by <code>ip delete</code> command, and then enter a new IP address.}}
 <pre>
 LYSH@MyHostName# configure			 // Enters configuration mode.

@@ Line 19: / Line 19: @@
 After accessing the CLI, you have to set an IP address on the device. Please refer to the [[CLI - Networking]] section to know how to configure an IP address. Following is a simple example.
 <pre>
 LYSH@MyHostName# configure			 // Enters configuration mode.

@@ Line 21: / Line 21: @@
 <pre>
 LYSH@MyHostName# configure			 // Enters configuration mode.
-configure# ip add eth0 192.168.0.3/24 192.168.0.1 // Configures an IPv4 address, subnet, and gateway.(i.e. 192.168.0.1)
+LYSH@MyHostName(config)# ip add eth0 192.168.0.3/24 192.168.0.1 // Configures an IPv4 address, subnet, and gateway.(i.e. 192.168.0.1)
 interface setting was added. Do you want to apply these settings?(y/n): y
 ...
-configure#  exit
+LYSH@MyHostName(config)#  exit
 </pre>
@@ Line 30: / Line 30: @@
 <pre>
 LYSH@MyHostName# configure
-configure# nameserver add eth0 8.8.8.8	// add a nameserver, 8.8.8.8, into the eth0 interface.
+LYSH@MyHostName(config)# nameserver add eth0 8.8.8.8	// add a nameserver, 8.8.8.8, into the eth0 interface.
-configure# hostname set NewHostName
+LYSH@MyHostName(config)# hostname set NewHostName
-configure#  exit
+LYSH@MyHostName(config)#  exit
 </pre>
 }}

@@ Line 46: / Line 46: @@
 {{note| If the web browser on your computer does not connect to the Management Interface, Check the following.
-* ping the IP address of the imRAD device from your PC or laptop.<br>
+* ping to the IP address of the imRAD device from your PC or laptop.<br>
-* ping the gateway IP address configured on the CLI from the deivce.<br>
+* ping to the gateway IP address configured from the device.<br>
 * restart the web server by entering <code>systemctl restart apache2</code> on the [[CLI_-_Services(daemons)#Control_the_Service | CLI]].}}
 }}

@@ Line 13: / Line 13: @@
 * Press the "enter" key one or more times on your laptop until you see the login prompt.
-[[File:console-login.PNG]]
+[[File:serial1.png]]
 }}
 {{step|4|